Sensormatic VM32 Betreibershandbuch Seite 31
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-8 Operator's Manual
3. Use the number buttons to enter the number of the Quick View you want
to display, and then press the View button.
If the Quick View exists for that camera, the camera will immediately point
to the pre-defined Quick View, and then zoom and focus automatically.
The following information appears on the LCD:
CAM 12
MON 3 VIEW 4
If you tried to call up a Quick View for a non-programmable dome, or if you
entered an invalid View number (any number greater than 96), the
T
OUCH TRACKER beeps.
Running Patterns
A Pattern is a sequential series of pan, tilt, zoom, and focus movements from
a programmable camera. You “teach” the camera a combination of these
movements. Then when you run the Pattern, the camera automatically repeats
the movements you taught it.
You can define your own Patterns to support your specific needs. Refer to
Chapter 3, “Defining Automatic System Functions,” for procedures on
defining Patterns.
When you run a Pattern, you can specify that you want the Pattern to run
once, or you can specify that you want the Pattern to repeat itself until you
stop it manually. Both methods are described here.
The Dome Configuration Worksheet in Appendix A allows to list which
Patterns are available for which domes. Make copies of this worksheet for
each dome installed at your facility.
The following procedure describes how to run a Pattern. Each programmable
dome can have up to three Patterns defined for it.
1. Use the number buttons to enter the number of the monitor where you
want the video displayed. Then press the Monitor button.
- View Manager 1
- Table of Contents 4
- Table of Contents v 6
- Before You Begin 8
- How To Use This Manual 9
- Text Conventions 10
- Related Documents 10
- Support Services 11
- About Your New System 12
- Understanding Your System 13
- System Features 13
- Typical Equipment 14
- Figure 1-1: Typical Equipment 15
- Monitors 15
- Modes of Operation 18
- Menu/Programming Mode 19
- About Your New System 1-9 20
- Sequencing Mode 21
- Alarm Mode 22
- 1-12 Operator’s Manual 23
- Output Devices 24
- Selecting Monitors 25
- Controlling Cameras 25
- Stepping Through the Cameras 26
- Controlling Zoom and Focus 27
- “Flipping” the SpeedDome 28
- MON 5 PEEL 29
- Displaying Quick Views 30
- Running Patterns 31
- Running Sequences 32
- Controlling Output Devices 33
- Controlling Dome Outputs 34
- Clearing System Alarms 35
- SRC: CAM 30 INP 4 36
- MON 3 ALARM 3 36
- SRC: CAM 33 INP 4 37
- MON 5 ALARM 4 37
- CHAPTER 3 38
- Defining Quick Views 39
- IMPORTANT 40
- Defining Patterns 41
- OUCH TRACKER only 42
- CAM 8 PATTERN 44
- MON 2 SAVED 44
- 3-8 Operator's Manual 45
- RECORD PATTERN 45 47
- FINISH W <NEXT> 47
- Sequence Programming Display 48
- 3-12 Operator's Manual 49
- Defining Sequences 50
- 3-14 Operator's Manual 51
- Alarm Programming Overview 52
- CAM12/1==> MON 5 53
- OUT CAM09 OUTP3 53
- Setting Up System Alarms 54
- 3-18 Operator's Manual 55
- 3-20 Operator's Manual 57
- On-Screen Programming 58
- Using the On-Screen Forms 59
- Setting Up Monitors 59
- CAMERA TITLES 60
- MONITOR SETUP 60
- Naming Cameras 61
- Using the On-Screen Forms 4-5 62
- DEFINE SEQUENCE 63
- SETUP VIEW 63
- SET TIME/DATE 63
- EVENT SETUP 63
- Using the On-Screen Forms 4-7 64
- Configuring Timed Events 65
- Setting Up Events 66
- Configuring the Event Timer 67
- EVENT TIMERS 68
- 4-12 Operator's Manual 69
- Clearing Scheduled Events 71
- Disabling Timed Events 72
- 4-16 Operator's Manual 73
- TOUCH TRACKER Utilities 74
- Selecting a Language 75
- Sequence only 76
- Adjusting LCD Brightness 78
- Turning Key Click On / Off 79
- Adjusting Key Click Volume 79
- Resetting a Dome 80
- Special Utilities 81
- Programming Worksheets 82
- Dome Configuration Worksheet 83
- A-4 Operator's Manual 85
- Setup Sequence Worksheet 86
- Setup Alarms Worksheet 88
- CAM01/1==> MON 5 89
- Timed Events Worksheet 91
- Twilight Sensor Daylight Dusk 93
- Switcher Setup Worksheet 94
- A-14 Operator's Manual 95
- Connections 96
- Alarm and Relay Connections 97
- B-4 Operator's Manual 99
- Software License Agreement 100
- C-2 Operator's Manual 101
- C-4 Operator's Manual 103
- C-6 Operator's Manual 105
- Glossary 106
- G-2 Operator's Manual 107
- Glossary G-3 108
- OUCH TRACKER that enables 109
- Glossary G-5 110
- OUCH TRACKER 111
- G-8 Operator's Manual 113
- OUCH TRACKER, 5-3 115
- OUCH TRACKER, 5-2 117
- Thank you for your time 118
- What do you think? 118
- BUSINESS REPLY MAIL 119
- 8000-2655-01 120
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern